Singleton

Aust. 02 6571 5177 or Int. +61 2 6571 5177

Toggle Nav
My Cart
breadcrum-img

Earthen Dam & Pond Sealers

  • Home
  • Earthen Dam & Pond Sealers

GOT A LEAKING DAM OR POND?

  • Fix it today with Water$ave
  • No need to drain precious water
  • Apply directly to the water surface
  • Simple DIY solution
  • No need for costly earth moving equipment
  • Creates a permanent seal

Water$ave Plug or Seep – which one is right for you?

  • water lossLess than 150mm (6 Inches) per week
  • leak locationWall
  • Extent of LeakWet area outside dam
  • Soil TypeFine/sandy
trans Water$ave Seep

Choose Water$ave Seep if

  • Water level drops by less than 150mm (6 inches) per week
  • The leak is in the wall of the dam
  • There are wet areas, but no flow of water outside the dam
  • The soil is fine or sandy
  • water lossMore than 150mm (6 Inches) per week
  • leak locationBase
  • Extent of LeakVisible flow of water
  • Soil TypeCoarse/Rocky
trans WATER$AVE PLUG

Choose Water$ave Plug if

  • Water level drops by more than 150mm (6 inches) per week
  • The leak is in the base of the dam
  • If a flow of water is visible outside the dam wall
  • The soil is coarse or rocky

Not sure which product is right for you?

Tell us about your dam and a Product Support Expert can help

POWERFUL POLYMER SEALS IN TWO WAYS

Water$ave Plug and Seep are super-absorbent polymers in a dry, powdered form. When applied to the water surface the polymer works to seal the base and walls of your dam or pond in two ways.

Firstly, the particles begin to hydrate and expand on contact with water and descend to the bottom of the dam. The weight of the water (‘head pressure”) forces the particles into the cracks and voids, where the polymer particles continue to expand, creating an effective plug to stop the leaks.

Secondly, the negatively charged particles create a flocculating effect whereby soil particles suspended in the water bind together and sink to the bottom. This material also assists in stopping the leaks. When applied correctly you can achieve a permanent seal in one application.

Tell us about your dam for free expert assessment
solution

A SIMPLE DIY SOLUTION TO A COMPLEX PROBLEM

The polymer is applied directly to the water surface by hand, or with the use of a small spreader.

If you know where the leaks are coming from, the polymer can be applied only to these areas. Otherwise it may be better to treat the entire water surface. Larger areas will require the use of a small boat as the polymers should not be broadcast more than 2m (7ft) by hand.

For best results Water$ave Plug or Seep should be applied while the dam is actively leaking. Also, the treatment area should be free of weeds and debris as these stop the polymer particles finding their way into the leaks. The water should be at least 1m (3ft) deep. We recommend using the product only on fine days, with little wind and no rain.

When applied correctly, there should be a noticeable reduction in water loss over the first few days. The full effect of the treatment can take up to 14 days.

HOW MUCH DO I NEED?

Water$ave polymers should be applied evenly at a minimum rate of 100gm per square meter (4oz per 10 square feet). Aggressive leaks may require more product to achieve the best results.

Click here to use our simple polymer calculator.

solution

FRIENDLY TO THE ENVIRONMENT

Water$ave Plug and Seep are non-toxic and not harmful to plant and animal life and are safe to handle without protective clothing. The polymers do become slippery when wet, so care should be taken. While there is no need to remove fish, it is recommended to keep livestock away during the application to ensure the polymers are relocated from the leaking areas. The polymers will bio-degrade over 8 - 10 years, during which time the natural build-up of silt and clay will have created a permanent natural seal.

 

TOP