Water$ave PL Plug Range

Polymer Innovations Water$ave Plug is the best polymer based dam or pond sealant that is 100% customisable to your specific environment.
Whether the leak is in the base, wall, through rock or any soil type Polymer Innovations has the specific Water$ave PL dam sealant to put an end to your water losses.

The best time to treat your leaking dam with Water$ave PL Plug is when there is water in the dam, especially after recent rain.
While there is water about & your dam is filling, stop those dam leaks before it costs you a lot more money.
Putting your crops, stock & livelihood at risk.

There are other ways of sealing your dam using such products as bentonite clay, lime or with a lining.
Most of these solutions have to be implemented when the dam is built.
Even then due to time or money restrictions these dams are not built as well as they should be where such things as soil conditions & seasonal changes are not considered.

Water$ave PL Plug & Seep is easy to apply.
Just sprinkle over the surface of the water on a quiet day from a small dinghy or boat.
Then allow 7 - 10 days depending on the rate of leak, to start saving water & money.

The Water$ave Plug Range is a blend of lineal & cross linked polymers that are 99% insoluble, non toxic & biodegradable.
It will not harm plants, fish, yabbies or livestock.

This polymer is known as a Polyacrylamide, a combination of two monomers: Acrylamide & Potassium Acrylate. It’s charge density & molecular weight can be controlled by the ratio of acrylamide & potassium acrylate.
This allows us to customise its charge depending on the soil to be bonded, even in silty or sandy soils.

Water$ave PL locates the leak & seals it.
Even if you don't know exactly where the leak is our polymers will locate the outflow & stop it.

Three Water$ave Plug Blends to suit all soil types & conditions:

• Water$ave PL Plug
  Is best suited to dams or ponds that contain any cracks & crevices that are wider than 4mm.
   Plug is perfect for soil types that are not too porous, dam walls or bases containing any rock or soil with cracking, larger pebbles, holes, tunnels or crevices.
  
  
• Water$ave PL Seep
  Is best suited to dams or ponds that contain fine porous soil types that contain cracks & crevices narrower than 4mm. 
  Seep is perfect for fine sandy or silty loams, basalt, clays & volcanic soils.
   
• Water$ave PL Bomb
  Is a specific slow release polymer for last resort major leakages in a general area.
  Not available online. Available to order after consultation with a Polymer Innovations representative.

When applied correctly Water$ave PL Plug is the easiest, most cost effective polymer dam sealing product on the market anywhere in the world.

Polymer Innovations Water$ave PL Plug Range key benefits include: 

• 100% customisable to your unique conditions.   
  
• Seals dam without the need to drain precious water.   
• Can be utilised into the soil during the construction of new dams.
• Cost effective, no need for heavy & expensive earth moving equipment.
• Customisable blends such as Plug, Seep & Bomb will seal the most porous of soils.
• Quick & easy application to full or partially full dams.  
• Specifically designed to locate the outflow & seal it.  
• Proven time & equipment saver. 
• Non toxic, biodegradable & environmentally friendly. Will not harm your livestock.
  

Our experienced staff will go through your problem step by step & customise the most effective solution for you.
They have been out there in the field for years dealing with all types of leaking dam scenarios. 

Polymer Innovations Water$ave PL Plug, Seep & Bomb come in a variety of easy to pour 2.5kg bags, & 5kg, 10kg, 15kg, 18kg(Seep) or 20kg(Plug/Bomb) pails.
Plug & Seep are also available in 500kg or 1000kg bulk bags & 32 or 48 pail pallets. 

Australia’s water conditions are often extreme & unpredictable; it is after all ‘the land of drought & flooding rains’.
The perfect testing ground for the world’s best dam sealing product.